(as of Jan 24,2022 23:02:15 UTC – Details)
Car care and repair can be expensive, especially if you don’t know what the issue is. While you can take it to a mechanic to diagnose the problem, having some automotive expertise and a DIY attitude can save you money and time by locating the issue yourself. To do this, you need an on board diagnostic II (OBD-II) scan tool. This automotive tool will communicate with a car’s on board computer system to see what issues the sensors and computer detect. To help boost you’re automotive detective skills, here’s our OBD-II scanner YOU should check out.
How to use YA101?
Locating Data Link Connector
1.Choose a location under driver side dash under steering wheel) and use that description in both places.
2.If unsure about location of dlc, check vehicle manual or reputable service center about location
Connect the tool
1.If the connector is not there a label should be there indicating the whereabouts of the connector.
2.If necessary, remove the cover from the DTC
3.Turn the ignition switch to the on position.Do not start the engine
4.Plug the OBD connector into the Data Link Connector.
5.The tool will attempt to identify the vehicle. If successful, the vehicle identified. if the vehicle cannot be identified, menus will be shown for you to select the vehicle manually.
How to verify whether the vehicle will pass the emission test with this code reader?
I/M Readiness: Displays a snapshot of the state of the vehicle’s OBDII Monitors.
* To review I/M Readiness status,make sure that the ignition key is switched to ON with the engine off.
* Not all monitors are supported by all vehicles.
There are two types of l/M Readiness tests:
* since DTCs Cleared -shows status of the monitors since the DTCs werelast cleared.
* This Drive Cycle-shows status of monitors since the start of the currentdrive cycle.
After entering the I/M Readiness, there will be 10 results on the list.
Misfire monitor, fuel system, component monitor, catalyst monitor, heated catalyst, EVAP system, secondary air sys, 02 sensor, O2 sensor heater EGRand/or WVT. There will be an OK if each of them works fine. [Not all vehicles have these 10 parts]
YA101 Code Reader Support Car List:
Need Standard OBD2 Protocols from 2000 to now
Need Standard OBD2 Protocols from 2003 to now
Need Standard OBD2 Protocols from 2006 to now
Need Standard OBD2 Protocols from 2009 to now
Support Car Models for OBDII diagnostic function:
(Note: YA101 only Support 12V cars, Does not support 24V Truck )
1.SAE J1850 PWM(41.6Kbaud)
2.SAE J1850 VPW(10.4Kbaud)
3.ISO9141-2(5 baud init,10.4Kbaud)
4.ISO14230-4 KWP(5 baud init,10.4 Kbaud)
5.ISO14230-4 KWP(fast init,10.4 Kbaud)
6.ISO15765-4 CAN(11bit ID,500 Kbaud)
7.ISO15765-4 CAN(29bit ID,500 Kbaud)
8.ISO15765-4 CAN(11bit ID,250 Kbaud)
9.ISO15765-4 CAN(29bit ID,250 Kbaud)
KINGBOLEN YA101 Specifications:
Screen: 1.8 ” TFT, 160*128dpi
Voltage Range: 9-18V
Operating Temperature :0℃ -50 ℃ (32 ℉ -122 ℉ )
Environment Temperature:-20 ℃ -70 ℃ (-4 ℉ -158 ℉ )
Dimension :125mm*70mm*22mm(4.65″ *2.68 ” *0.88 ” )
1pc * YA101 Code Reader
1pc * English User Manual
1pc * Carton Box
What are the Functions list of YA101 OBD2 Scanner ?
Read Codes Reads DTCs from vehicle’s computer with KOEO or KOER. Erase Codes Deletes DTCs from vehicle’s memory. Live Data Live Data menu lets you view, record and playback real time PIDs data fromthe electronic control module. In live data menu, you can insert the selected item to front by holdingpressing the key for 3 seconds. Freeze Frame Displays a snapshot of operating conditions at the time of a fault. Vehicle Info Scan tool displays the vehicle’s VIN number, Calibration ID (s) and CVNthat identify the software version in the vehicles control module (s.)The tool also displays In-Use Performance Tracking of importantreadiness monitors. Component Test Tool will display a list of components and their locations on the vehicle. This function will always appear on the Main Menu. This selection will appear on the Diagnostic Menu only when the tool has a list of component locations for the currently selected vehicle. On-Board Monitoring Scan tool controls the operation of vehicle components, tests or systems. O2 Sensor Test Displays oxygen sensor monitoring test results from the vehicle’s memory,the O2 Monitor Test is NOT an ON-DEMAND TEST. I/M Readiness Displays a snapshot of the state of the vehicle’s OBDII Monitors. DTC Look Up Looks up definitions of DTCs stored in scan tool, and shows the possible causes of the DTC. (NOT every DTC with possible causes reason) Voltage Test This function is used to monitor the voltage present on pin 16 of the OBDIIData Link Connector. Data Logging Turn on /off the data log function to record the device data through vehicle. Self-test Display Test. Used to check the display screen. Keyboard Test. Verifies that the keys are working correctly. Update Pls install update tool from Official webiste, and copy the newest firmware ,paste to the YA101.
【NO EXTRA BATTERIES OR APPS REQUIRED】 No need battery nor internet connection, just plug the obd2 scanner for car into obd2 port to reset check engine light. The car diagnostic code reader is suitable for US-based car made after 1996 and EU-based car made after 2000 which equipped with OBD2 (OBDII protocols: KWP2000, ISO9141, J1850 VPW, J1850 PWM and CAN), which is for 12V car and light truck.
【TURNING OFF THE CHECK ENGINE LIGHT】With YA101 model you never have to worry about the illumination of the Check Engine Light as it successfully turns off the said light, clears the relevant code and also reset the display.
【EXTENSIVE TROUBLE CODES CATALOG】 The device boasts an expansive catalog of trouble codes along with their detailed descriptions to ensure tech peak performance of you’re vehicle all the time. YA101 scanner also features the capability to foretell whether your vehicle would pass or not in the O2 sensor test even before you take it to a test center.
【SIMPLICITY OF DESIGN】 A good scanner must be easy to operate. It features the simplest of design with only a couple of buttons which makes it easier to read and clear the codes in a faster way. The device sports a nice backlist LCD display which is clearly legible at all conditions. The display also offers a convenient multilingual menu at the same time.
【LIFETIME FREE UPDATE AND MULTI-LANGUAGE】We provide 100% Full Refund & Return Guarantee and 3 YEARS Free Warranty. YA101 allows users change the language, including English, Chinese, France, Deutsch, Italian, Japanese, Espanish, Russian, Portuguese
The KINGBOLEN OBD2 SCANNER is a full-featured code reader that supports the OBD2 protocol. It checks EVAP and O2 sensors and can also diagnose engine problems. This scanner is able to support all OBD2 modes, including MODE6 with DTC lookup. You can find out if you have a problem with your car or if you need to take it to the repair shop.
This Bluetooth OBD2 scan tool supports OBD II protocols and the OBD standard. It can read error codes and displays the current sensor data. The YA101 model is compatible with most gasoline-powered vehicles, but it does not support diesel or hybrid vehicles. The YA101 can also be used with pickups that use 24V voltage. It can also read trouble codes without a computer and requires no extra batteries or internet connection.
This OBD2 scan tool features a bright 2.8-inch color display and can read trouble codes. The YA101 scanner has an easy-to-use 8-key interface that allows you to select from a variety of major categories. The YA101 has a built-in reset feature that resets the vehicle’s dashboard to the default settings. This allows you to clear codes quickly and easily.
As more vehicles are being equipped with non-engine control systems, the KINGBOLEN OBD2 SCANNER supports the full OBD2 protocol. This means that it is able to identify and repair problems on most modern automobiles. The ediag TPMs support the full OBD2 protocol. It requires a 9-volt battery for power. The KINGBOLEN OBD2 SCREEN is capable of detecting fault codes in vehicles with OBD2 protocols.
The YA101 OBD2 SCANNER offers a 2.4-inch color display and supports 9 languages. The ediag OBD2 SCANNER has a wide coverage range and features a multilingual menu and a comprehensive trouble-code database. A YA101 OBD2 SCANNER is a great investment for most types of cars. Its user-friendly interface and a backlist LCD display make it easy to navigate the menu.
Unlike many other automotive diagnostic tools, a CANbus Reader allows you to view data from a car’s OBD2 port. It also reads error codes and displays data from the current sensors. The YA101 supports the OBDII protocol and has wide compatibility with gasoline and diesel vehicles. However, it does not support some vehicles with 24V voltage, such as pickups.
The kingbolen OBD2 Scanner is an excellent choice for people who want to diagnose a car. Its full OBD2 protocol support and battery-powered design makes it a good option for a variety of vehicles. While the kingbolen OBD2 SCANner is a good choice for most people, it also offers useful features for those who want to diagnose their cars.
The KINGBOLEN OBD2 SCANNER is an excellent choice for drivers who want a high-quality device that works on any vehicle. The scanner is compatible with most domestic and import cars. It is also compatible with most European and Asian vehicles. The kingbolen OBD2 SCANNER is a good option for people who drive older cars. The YA101 supports a wide variety of gasoline and diesel vehicles. It is not a good choice for pickups with 24V voltage.
The KINGBOLEN OBD2 SCANNER can connect via Bluetooth with your car. It works with most vehicles, including those sold in Australia. It is compatible with all OBDII protocols. The KINGBOLEN OBD2 scanner has Bluetooth connectivity and connects with the Android app via Bluetooth. Its size and weight is also a factor. If you want to purchase this diagnostic tool, you should consider whether you need it.
The OEBD2 connector supports a wide range of gasoline and hybrid vehicles. While most cars are compatible with these plugs, they will not work on trucks, pickups, and hybrid vehicles. A CAN-compatible OBD2 Scanner will work on the CAN bus, which is a standard protocol for connecting to a vehicle. If you need a Bluetooth connection for your car, you should purchase a KINGBOLEN OBD2 SCANNER.
The KINGBOLEN YA-101 OBD2 Scanner is a compact tool that is light and portable. It features a wide range of diagnostic functions, such as the ability to check batteries from 6V to 12V. It also has a lifetime warranty and free firmware updates. Its small size allows you to place it anywhere and use it during repairs. When you need to test the car’s battery, the KINGBOLEN BM-560 is the perfect tool.